Electric Fireplace Wall Hanging Ideas
The wall-mount electric fireplaces are ready to use right out of their box. These electric fireplaces are an excellent way to add the ambience of your home without the need to remodel or venting.
They're usually heavy and require careful installation. Follow these steps to set up your new electric fire correctly.
1. Connect the Brackets
A wall-mounted electric fireplace or recessed electric fire instantly transforms any room. It's the ideal solution for homes without an existing fireplace opening, or for apartment dwellers.
Decide where you want to put your electric fire. It is important to choose a location that won't be susceptible to moisture and at a minimum of a few inches away from furniture, drapes, and other areas with a lot of traffic. Mark the wall with layout marks that indicate the top and bottom plates for the fireplace frame.
Use a drill or other tool to make exploratory holes in the wall. Find studs using a stud-detector and mark the drywall according to the location of the brackets for mounting your fireplace. Then, patch and paint the wall or create a wall to prepare it for fireplace installation.
Depending on the wall-mounted fireplace, you could have to either install the screen and firebox as one unit or separate them by the use of a wall bracket. If you're unsure about your ability to handle this task on your own, you might consider hiring a general contractor or experienced carpenter.
You can find an installation template that comes with all electric fireplaces. However you should keep a spirit level handy and pencil to mark the exact spot where the wall brackets will be placed. Make use of the template to ensure that the power cable of the fireplace is able to reach a nearby outlet to connect it.
Install drywall as smooth and as flush as possible to give the fireplace a clean look. Add a trim piece to the bottom edge and then sand and paint the entire frame for an attractive appearance.
Most wall-mounted electric fireplaces have hooks or slots on the back of the unit which you can insert into the slots or hooks on the mounting brackets. Be sure to align the slots or hooks prior to connecting the brackets for your fire. Once the fire is in position, you can add any additional elements such as crystal embers or driftwood log pieces or decorative rocks.
2. Check the Bottom Bracket
The space above a fire mantel, chimney breast or mantel is a prime spot to hang artwork. However, there is a line of distinction between an artistic arrangement & one that distracts from the overall appearance of the fireplace's design.
The general rule of the thumb is that a painting should be at least 80 percent the length of the fireplace or mantel it is placed above. This will help keep it in proportion and make it look good on the wall. Other decorative and ornamental items placed on the mantel may affect the size and proportional guidelines.
If you're planning to hang a picture above your electric fireplace, you must ensure that the frame is made of glass or other material that can withstand high temperatures. If you're not sure whether the frame is suitable, a quick test using a temperature-sensitive cloth will show whether the frame is suitable for this type of application.
A common concern with displaying pictures over the fireplace is the possibility of damage to the artwork from smoke or heat that escapes. Although this is rarely an issue with traditional wood or gas-powered fireplace, it's a good idea to check the recommendations of the manufacturer if you're planning to install an electric fireplace that is mounted on the wall.
Most electrical fires have mounting brackets that can be attached to the wall using either hanging screws or wall-mounted fixing systems. If the latter, it is recommended that you drill exploratory holes into a discrete part of the wall before you attempt to mount your electric fire. Then you can use an instrument to locate cables and pipes to ensure whether there are any cables or pipes within the vicinity of the location you've chosen to mount it.
If so, you could place your fire on the electrical socket or move it to a new place. If you move it to a new location, you'll need to ensure that the power cable can be able to connect from the fire to the electrical outlet - this is crucial for older homes or homes with solid walls. If not, your electric fire won't perform as it should. Some models come with templates that show you the locations to drill holes, while others require you to use an apex level and pencil to mark the locations on your wall.
3. Connect the Power Cord
You may have to move your plug socket to the back of the unit if you have installed a fireplace that is recessed. This can create a sleeker look. First test the fireplace to make sure it is operating properly.
The third way to mount an electric fireplace is by framing the room and then building it into the wall. This gives you a traditional, finished look and allows the installation of the installation of a mantel. The owner's manual for your particular model will give details on framing, wiring, and securing the fire place.
When you're ready to install your new electric fireplace on the wall, start by marking the location of installation with a marker or pencil. Then apply a carpenter's level to ensure that the installation location is flat and level. You can use a studfinder to mark the location so that you know that you're drilling in a safe location.
Use the electric drill after you have marked the installation location to make holes for bracket screws or hanging screws. Follow the steps in your owner's guide for this step. This is especially crucial if you're installing the fireplace into the drywall. If you're unsure of the best way to go about this you can always ask a professional to take care of the installation for you.
A cable organizer kit can be used to conceal power cords. These kits typically include sleeves, clips or boxes for bundling cables. wall hanging electric fires can also use fish tape or wire snake tools to help guide the cords along the wall. If you don't want to cut into the drywall, a Powerbridge kit will provide a cleaner and more secure connection.
Additionally, you can disguise the wires with paintable covers or by adhering them to the wall and skirting boards. Be sure to keep the cover or tacks away from the source of heat, however. This will help prevent accidental contact and protect the cord.
4. Connect the adapter
A wall-mounted electric fireplace is a great choice for home renovations or for those who do not have the space or funds to build a gas fireplace. They are easy to install and come ready to use straight from the box. They are a wonderful alternative for those looking for a chic modern design or the warmth a fire provides. These units are designed to be hung like art on any wall. They can be recessed or not at all recessed and are fully electric and have heating powered by fans.
It's a good idea to make an inventory of all the tools and equipment you'll require prior to starting the installation process. You can find the complete instructions on how to mount an electric fire in the user's manual. Some models might require you to attach the brackets directly onto the wall, while others may have a mounting plate that can slide into slots or hooks on the brackets for mounting. It is crucial to eliminate all combustible materials from the area in which you are installing a recessed unit. In general they should be kept 3 feet away from the front side of the fireplace and 1.5 feet away from its sides.
After you've checked all components, you'll need to connect your electric fireplace and ensure that it is working properly. This is an essential step because it will guarantee that the flame effect screen and heater function in the way you intended. This will give you an idea of the final product in its final configuration.
Cover the cord after you are confident that it's working correctly. This will keep the final product neat and neat. electric fireplaces wall mounted can be accomplished by applying paintable wire covers, or install a new outlet that allows you to put the cord behind the unit. This will give seamless finishing to your fireplace.